Skip to content
HearingTracker
Log in

Programming the Oticon Alta Pro miniRITE

This topic is closed.

25 replies17.6k viewsLast reply

Jump
Link to this topic

Scroll down to see all the steps for programming the Oticon Alta Pro MiniRITE.

>>Links-for-Hearing-Aid-Self-Programming500<< may answer questions you might have.

This is my USB mini Pro. There are many like it, but this one is mine. My mini Pro is my best friend. It is my life. I must master it as I must master my life. My mini Pro, without me, is useless. Without my mini Pro, I am useless. :smiley:

Cable to connect mini Pro/Hi Pro to your PC

Standard CS44 Programming Cables (same as Oticon Programming Cable #3)

Closeup of CS44 Programming Cable

Flexconnect # 390-01-180-05 (pair)

Closeup of Flexconnect

Ready to Connect Oticon Alta Pro miniRITE

Diagram of how to connect Oticon Alta Pro MiniRITE
Red dot on small plug of cable end matches red mark on Flexconnect plastic base
Black raised dot on Flexconnect faces upward
Batteries remain inside the hearing aids

Connected and ready to go

Connected also to mini Pro and ready to run Oticon Genie fitting software

Happy programming…

14 people in this conversation8 min readJump to latest

pvc,
I subscribed to this thread.
So, the Hi-Pro can program several brands and models?
I have a 2012 ASUS laptop running Win 8.1. It does have a serial port on the side. Of course USB is better…
I am confident that I will be wanting to program as I get into this. “Patience, Glasshoppa…”, OK…

Edited

I do not make my signature visible. The forum software makes signature information visible. You should seek a solution that includes professional support. I think you need that support. Have you looked at solutions offered at Costco?

Hi pvc
(and all fellow deaf and not dumbers on this forum)

THIS IS URGENT HOPE YOU ARE STILL AROUND

I’m a new member here, so please bear with me… this post re the Oticon Alto seem dated now but still relevant to me cause am looking to buy a pair OTICON RIA 2 PRO TI, the 85db one due to my ski slope (high tone profound deafness) that is somewhat worse than yours.

My Q is simple - do these instructions about programming the Alta using the USB mini Pro still apply now for/to the Ria 2 Pro, given the Ria 2 Pro is within the same family as the Alta and the Nera, now called “Legacy” by Oticon as result of Opn? Should I rather look to procure a NoahLink even if it is more expensive - will that work to program the Ria 2 Pros?

BOTTOM LINE
What do I need to the Ria 2 Pros (and its family)
-Software, yes I noted the Genie links
-Hardware, this is what am really not sure about

*BTW I’m a life long user of Oticon but over last year really got fed up with this “Microsoft” way of forcing people to the next gen, while the last gen still works just fine. With every new version of the HA they say they have now done something yet more radical re, e.g. even more x% focus bla bla bla within a noisy environment, while the “Legacy” version brochure stated excactly the same, just 1/2/3 years back…

…and the PRICES have forced me to now go the route to procure HAs via the Internet and DIY, this is simply not working for me, my ex-audiologist did not even know how to program my last pair of Oticon Epoq XW then top of the range HAs - I had to show her… NO MORE

I’m hoping for a response, like really

Hi and thank you for a wonderful guide. I am currently downloading the Oticon software. I found the mini Pro and the CS44 cables on AliExpress. However, I am unable to find a source for the Flexconnect # 390-01-180-05. Any idea where two of these could be purchased?
Thanks,
Frank

Hi,
I have finally obtained the Oticon software, Mini Pro, CS44 cables and Flexconnectors. Using the above guide, I can’t seem to get the software to detect my Alta Pros.

Running Genie 2017.1, under preferences, I can click “DETECT” under Programming Device and “HI-PRO VER 02” is listed with the serial number. The “SELECT” button next to “DETECT” is grayed out.

Running Genie 2, the detect button in the upper left is grayed out. If I click “Update instrument firmware” the firmware updater opens, the yellow pc light flashes several times, then the blue flashes, then the red flashes and a message says “No instruments detected. To detect instruments, use a cable connection”

I have checked all connections several times. Any ideas how to proceed?

Thanks,
Frank

I finally got a Hi-Pro USB on Amazon with US-based delivery. Cost a little more but I will only have access to my desktop PC for a few weeks before I’m off to Las Vegas with a Linux Mint based laptop.

One key point to be aware of. Genie software apparently expected to see the Hi-Pro as Com Port 1 thru 4. Mine had auto configured to Com5 but I changed it in Device Manager to Com2.

Installed the software, changed the com port, plugged in the USB and the lights happily came on. Hooked up the cables to the ribbons, changed the batteries in the aids, snapped the ribbons in place >as instructed on Genie (thank you, Oticon). Son of a gun. The Hi-Pro was detected and my aids were detected. YAYYY!!!

I feel a little like a dog chasing a car…what does he do when he catches it?

I’d love to link up with someone self-programming their Oticon hearing aids using the Genie 1 software as opposed to Genie 2 which is for the newer aids.

I went in and set myself up as a client, selected the family as Alta2 Pro Ti and updated firmware on my streamer. I stepped through fitting without touching anything and saved the configuration as a standalone database vs. reprogramming the aids to what they had already as a configuration baseliine.

There are SO MANY OPTIONS…some obvious, some not so obvious that I’m a bit overwhelmed at the moment. I want to make sure I actually captured the instruments’ current settings as a “Genie baseline file” before I start going crazy. I’m working hard at being patient and taking lots of time.

All pointers and advice, especially Oticon-based, greatly appreciated.

Congratulations.
It is a good feeling.
My understanding of hearing aid software is the more you learn the more you realize you don’t know. It’s that deep.

You are not alone with the Genie 1. You will have comrades.

I’ve only used Genie to change a couple of options on my Streamer as I don’t have the connectivity hardware for my .

I think perhaps the key thing to do is either backup your existing settings if possible or take screenshots of the settings screens as they are now so you can ‘undo’ any ‘mistakes’ if necessary.

Additionally, I’d only ever change one thing at a time so you know exactly what you changed and the impact it had.

One last thing - make a notebook to act as a ‘change-log’ so you have a journal of what you have tried.

In reply to @capecuddy

To add to davart reply, with Phonak there is a place in the software to add notes on each session.
Another thing I do is add a client. This way you can leave the original programming alone. Use this new client to copy the programming and then try things. One thing at a time can be the smart way. My latest new client is Joe Blow.

I use Google Keep checklist style notes. I record my observations and likely next actions via tablet or phone or PC…stored in cloud. Then I get into Genie and work them off, crossing them out as I go. When I’m done with Genie, I reboot into Linux Mint because I just can’t take Windows any more than I have to these days. A total meltdown caused by their “quality update” forced me to finally bite the bullet and I love it.

Related discussions