Hearing aids turning off when I put my headphones on

@legsmaniac69 said:

It would if the aids are switched to coil/loop only (no Mic option) thereby the aids cannot pick up any outside sounds

The outside sounds are getting direct to my ear drums, not from the HAs, but through the open domes that I have (and much prefer to the closed domes I have tried, by the way).

I think the Compilot 2 does provide stereo sound via Bluetooth.

@legsmaniac69 said:

Do you have an magnets to hand? Some strong fridge magnets or whiteboard magnets perhaps?

Good idea. I put a fridge magnet next to the HA and low and behold it turns off.

Also, not sure what this proves, but I tried putting the HAs in the charger and removing them straightaway. They still turns off but do not turn on automatically. I also tried fitting them in the charger with the charger disconnected from the mains. They don’t turn off.

So it seems magnets are doing something different to what the charger does. I had read somewhere in the forum that there is special mode for using the HAs with a phone and that this is activated by the magnet in the phone speaker. However, my HAs, are not affected by putting a phone next to them.

@Bugtao said:

However, my HAs, are not affected by putting a phone next to them

The phone has to be really “old school” to do it. Our Panasonic cordless handset doesn’t have a strong enough magnet to do it, our REALLY old “Princess” phone does.

@legsmaniac69 said:

Since the Compilot only has one single loop that feeds both coils in the hearing aids simultaneously, there is no way you can get a true stereo effect.

I’m not sure how it communicates but I dont think it is tcoil. I can confirm that it is stereo. There is no doubt about that.

Apologies. Seems my understanding of the ComPilot was wrong. I’m guessing the “loop” is either merely something to hand around a neck or some kind of “aerial” for transmitting whatever mode it uses. I understand now it doesn’t use the pick-up coils but it’s own internal wireless transmission/reception. Similar, I guess, to the iCube. So yes, stereo would certainly be possible in this way. Thanks all for the corrective info.

Wish I could get one now. Just a shame they’re SO expensive. A bit overkill for me just to listen to music with.

@Bugtao said:

I put a fridge magnet next to the HA and low and behold it turns off.

Also, not sure what this proves

It merely proves it’s definitely magnets in action. Why is obviously yet to be ascertained.

@Bugtao said:

I tried putting the HAs in the charger and removing them straightaway. They still turns off but do not turn on automatically.

Maybe they’re set not to when they detect a charge?

@Bugtao said:

I also tried fitting them in the charger with the charger disconnected from the mains. They don’t turn off.

Electro-magnet?

@Bugtao said:

I had read somewhere in the forum that there is special mode for using the HAs with a phone and that this is activated by the magnet in the phone speaker.

Yes, I saw that too. But you also confirm that you hear the “turning on jingle” which implies they’re turning off? If they are switching to the pick-up for telephones then surely you would hear the headphones thru the coil as the speaker coils still produce some EMF. Again, you could test this with the fridge magnet, placing your ear next to something electrical, such as a charger transformer like those used for charging phones. You should hear the electric hum of mains if the coil is activated. That is, assuming your aids have been programed with that function.

All the above is merely guesswork again really and at the end of the day, your headphones cause you a problem due to the magnets, that much we do know. Wonder if it’s a function that could be turned off in the programming? Since you don’t use the telephone in that way it’s not a feature you need, I presume? That would certainly solve your problem.

There’s one carrier at 10.5MHz of 500KHz bandwidth, looks digital. No idea what the encoding is as I’ve not had time to investigate it further but this one pops up whenever the ComPilot starts talking. My aids have one antenna for the tcoil (omitted if not fitted) and another for the 10.5MHz comms used for receiving streaming as well as transmitting program changes and beamforming audio when in stereozoom between the aids.

@Bugtao said:

So it seems magnets are doing something different to what the charger does. I had read somewhere in the forum that there is special mode for using the HAs with a phone and that this is activated by the magnet in the phone speaker. However, my HAs, are not affected by putting a phone next to them

I have the WH1000-XM2 and I get the exacty same thing with my Sky Qs. As well as the phone magnets never being strong enough to activate the profile - ah well. The profile change with headphones stops when I turn off the “EasyPhone” function on the phone profile in Target.

Yes, sorry for being a bit slow…

It’s ok.
That’s how I learn too.
I also have a pair of the Audeo B90 13 aids.
Very nice aids.

All sorted now. Had the acoustic phone mode removed.

Also had some manual programs added at the same time. So far have only really tested the music program. It works great. Music from the headphones sounds good straightaway. It was pretty good with Autosense too, but I think the music program is better. It might be my imagination, but it seems to take quite a while for Autosense to adjust to the music. After 10 or 15 minutes it seems to sound better.

I’ve also found that the music program significantly reduces wind noise. An unexpected bonus. It seems to work better than “speech in wind”.