Skip to content
HearingTracker
Log in

Mute on Phonak Audeo Paradise P90

This topic is closed.

27 replies5.1k viewsLast reply

Jump
Link to this topic

Phonak Paradise P90 users: does the mute function just turn off the hearing aid mics, or does it also turn on the noise cancelling? If it doesn’t, is that (mics off, noise cancelling on) something that can be done in a custom program? Thanks in advance,

13 people in this conversation5 min readJump to latest

In all programs except calls it turns off the hearing aid mics.
Noise cancelling can be adjusted in the app when aid is in autosense, but not for streaming and custom programs and mic programs.

There is, at this time, no ‘noise cancelling’ in hearing aids in the same way it exists in noise cancelling headphones.

Noise canceling usually works by sampling the sound, reversing the phase of the electrical signals and feeding the reversed signals back so as to cancel the unwanted sounds. The microphones have to be on for this to happen.

@djheymann said:

If I mute the microphones, will that cut the ambient noise but not the bluetooth audio?

I believe the mute function on the aids literally mutes them.

While streaming you can adjust ambient/streaming sound if the aids are set up that way in the Target software by using the volume toggle switch on the aids.

Edited

In reply to @djheymann

You have 3 options to choose from, your fitter can set these using his software (Target):
When streaming:

  1. Default: your aid’s volume button (up/down) are used to mix the loudness. More of ambient sound or more of streaming source sound. Up -> Streaming is louder. Down -> ambient sound is louder.
    I found this not satisfiyng, since the ambient sound cannot be switched off completly. And if I want to mute the mics it causes to increase the loudness of the streaming sound.
    Or
  2. Disable the mics when streaming. (in Target-SW: Fine tuning, Autosense, streaming program options). This cuts the ambient sound completely off, up/down buttons change the loudness of the streaming source
    Or
  3. Long press button down to mute/unmute ambient sound. (in Target-SW: Device Options)
    Muted: This cuts the ambient sound completely off, up/down buttons change the loudness of the streaming source.
    Unmuted: up/down buttons change the loudness of both ambient and streaming simuntaneously

For phone calls with your mobile the ’s microphones are always ON. But again, you here no ambient noise.

And no, this has nothing to do with noise cancelling. It only mixes the microphones signal to the output signal as it is set in the options. If you have an open dome fitting, the effect will be less. Since the ambient noise bypasses the HA.

Edit: I double checked it in Target, and made some ammendments.

Need some clarification here. I have the Paradise UP Naida and had the audiologist provide me with a mute button, but when switching, it still seem like I’m hearing something. Unlike when I open the battery door.

I’m not sure I understand your question. I try my best to answer:

  • When streaming: mute reduces the environmental sound (mics), while the streaming sound is kept at the same level.
  • when not streaming: mute reduces the environmental sound (mics)

Does this answer your question?

I understand the streaming point, but when not streaming, I somethings want to just have my “god given” mute on, without opening up the battery compartment. With the Paradise, when I select mute, it is different from opening the battery. There seem to be a slight sound.

Ok. To mute you need to long-press button down on one of the . There is no confirmation tone, but the environmental sound is reduced significantly. This has to be activated by your fitter in his Target-SW.
I think, it’s just about right to have a quiet relax-time. :blush:

Thanks, that exactly how I have it setup and you pointed out that the environmental sound is significantly reduce, but not turned off. Technically, I don’t count this as Mute, but ok.

@Zebras said:

It sounds like I can’t hear anything

Yeah, mine are also almost completely mute. I need to scratch the mics to confirm the mics are not off.
I did also double-check in Target. There is no possibility to set the volume for the muted option.

Related discussions